Silverado Tire Pressure Sensor Reset

When your car’s tire pressure sensor light is on, it could mean that you need to bring your car in for a service or tire change. The silverado tire pressure sensor reset is easy and can be done at home with just a few simple steps.

What is the Silverado Tire Pressure Sensor?

The Silverado Tire Pressure Sensor is a system that monitors the pressure of the tires on your Silverado. When the system detects a low tire pressure, it will reset the air pressure in all of the tires to their recommended PSI level. This ensures that you have optimal tire pressure and prevents over-inflation, which can damage your tires and increase your risk of getting a flat. If you don’t see your Silverado’s Tire Pressure Sensor light coming on, or if it’s not working correctly, there is a chance that it needs to be serviced.

How do I reset the Silverado Tire Pressure Sensor?

To reset the Silverado Tire Pressure Sensor, you will need to open the hood and disconnect the battery cable. Then, use a flathead screwdriver to pry open the pressure sensor cover. Once you’ve opened the cover, press down on the black tire pressure sensor spring and pull it out of the sensor. Finally, replace the pressure sensor and close the cover. reconnect the battery cable and start your Silverado.

A Beginner’s Guide to Resetting the Silverado Tire Pressure Sensor

If your Silverado is having trouble keeping up with the traffic on the road, there’s a good chance that one of its tires is low on pressure. While it’s not an emergency, low tire pressure can lead to increased wear and tear on your suspension, as well as decreased fuel economy.

Here’s how to check your tire pressure, and if it’s low, how to reset the Silverado Tire Pressure Sensor:

  1. Locate the silverado’s tire pressure monitor located under the driver side floor mat. The sensor will have two hoses coming out of it- one for inflation and one for deflation. Loosen both hoses by turning them counterclockwise (as viewed from the front of the vehicle). Do not remove them yet!
  2. Once both hoses are loose, inflate each tire to 36 psi (245 kPa) using the inflation hose. Be sure to hold each valve closed (with your hand) while inflating each tire. Wait until each tire has reached 36 psi before releasing the valves.
  3. Now loosen both hoses again by turning them clockwise (from the front of the vehicle), and remove them from the sensor. Be sure to replace both hoses securely into their respective locations before driving away!

How to Reset the Silverado Tire Pressure Sensor

If you’re experiencing abnormal tire wear, a faulty pressure sensor may be to blame. The sensor measures air pressure in the tires and sends data to the engine control unit (ECU) to maintain optimum tire pressure. To reset the sensor, perform the following steps:

  1. Remove the wheel and tire assembly from your vehicle.
  2. Locate the silverado tire pressure sensor on the wheel hub near the brake rotor.
  3. Hold down one of the caliper pistons while unscrewing the screw that attaches the tire pressure sensor to its mounting plate.
  4. Remove the Tire Pressure Sensor from its mounting plate by gently pushing it out from one end then pulling it free from the wheel hub.
  5. Rinse and dry off all components before reassembling your wheel and tire assembly in reverse order with new screws and bolts replacing those that were removed in step 3 .

Additional Resources

If you are having trouble resetting your Silverado’s tire pressure sensor, there are a few resources available to help. Chevy’s website has a brief guide on how to reset the sensor, and several online forums offer tips and tricks for resolving the issue. If all else fails, you can take your vehicle to a mechanic for assistance.

benefits of resetting a tire pressure sensor

There are many benefits to resetting a tire pressure sensor on a Silverado. Here are just a few:

  1. Fixing a incorrect setting can result in decreased fuel economy and increased emissions. Resetting the sensor corrects this issue.
  2. If the sensor is not reset, it may become clogged over time, resulting in reduced air pressure and decreased range of movement.
  3. Over time, the seal between the wheel and tire may deteriorate, allowing air to escape and causing the tire to over-inflate. A properly reset sensor will help reduce or prevent this from happening.

What causes the tire pressure sensor to fail

The vast majority of tire pressure sensors in modern vehicles are digital and use a microcontroller to keep track of the tire pressure. Over time, these sensors can become faulty and fail to produce accurate readings. There are a few different reasons why this may happen, but the most common cause is interference from metal objects nearby the sensor.

If your silverado is experiencing problems with its tire pressure sensor, there are a few things you can do to try and resolve the issue. First, it’s important to rule out whether or not the problem is due to interference from metal objects near the sensor. If the sensor is working properly but readings are still fluctuating, then you may need to replace the sensor. If however, readings are consistently inaccurate even when no metal objects are nearby, then your microcontroller may be failing and you will need to replace that too.

How to reset a silverado tire pressure monitor

If your Silverado has a tire pressure monitor, you may need to reset it. To reset the tire pressure monitor, follow these steps: Disconnect the negative battery cable. Open the hood and remove the air cleaner assembly. Remove the four screws that hold in the upper shroud. Lift up the shroud and locate the tire pressure monitor. Reset it by pressing down on its black button and releasing it. Replace the shroud and tighten the screws. reconnect the negative battery cable.

Why reset a tire pressure monitor

If your Silverado is exhibiting odd tire pressure readings, it may be time to reset the monitor. A tire pressure monitor reset will help to ensure accurate readings for the remainder of the trip. This procedure can be done on either a manual or automatic Silverado.

To perform a manual tire pressure monitor reset:

1 Park the car in a well-lit area.

2 Remove the wheel and tire assembly.

3 Check that all four tires are inflated to their specified psi rating (PSI is printed on the sidewall of each tire).

4 Open the console and locate the silver connector for the TPMS sensor.

5 Disconnect the sensor from its connector by gently pulling on it while holding on to one end of the cable. Be sure to hold onto both ends of the cable during this step!

6 Once disconnected, place the Sensor Cap over top of Sensor and screw it in place (Photo 1).

7 Reinstall wheel and tire assembly, making sure that ALL fasteners are tightened properly (Photo 2).


If replacing or repairing a TPMS sensor, remove these five screws securing cover: 3 at front edge just below glove box opening; 2 in middle; 1 at rear edge just above trunk floor.

Add Comment