The TPMS system is designed to alert you when the pressure of one or more tires is low. Since 2007, the United States has mandated that all new vehicles have this safety feature installed.
The TPMS sensor comes fitted inside the tire. When it detects a problem, it sends a message to the control module of the car. This triggers the warning light on the dashboard of the vehicle.
Check the Tire Pressure
When your car’s Tire Pressure Sensor Fault message appears, it means that one of your tires isn’t properly inflated. This can cause issues with fuel economy, braking and handling, as well as serious damage to your tires’ lifespan.
Most modern vehicles have TPMS systems, which are designed to warn drivers when their tires aren’t at the proper air pressure. These warnings can save you money and help you avoid a blowout or tire failure in an emergency situation.
Your TPMS system uses sensors to measure the air pressure in your tires, which transmits the data to the TPMS control module via a signal receiver. If the TPMS detects a fault with any of these sensors, an error code is displayed on the dashboard or center screen in your vehicle.
You can check the pressure of your tires in a variety of ways, but the most common method is to use a gauge. These devices are usually located in the valve stem and can provide a stick, dial indicator or digital readout.
Before you start checking your pressure, ensure that the tires are cold (meaning they haven’t been driven on for a while). That way, the air isn’t as warm and the gauge can pick up a more accurate reading.
Next, remove the screw-on cap from the valve stem. Press the gauge’s fitting on the valve stem in a firm motion and wait for the device to prompt a reading. Compare this to the manufacturer’s recommended psi for your setup.
If the psi reads higher than the psi in your vehicle’s owner’s manual, it’s time to take your vehicle to a professional tire technician for repair or replacement. If the reading is low or you’re unsure of your results, repeat the process and try again.
Regardless of which type of tire pressure gauge you have, the most important thing is to follow the manufacturer’s recommendations and check your tire pressure regularly. This will not only prevent a TPMS error code but also save you from costly repairs down the road.
Reset the TPMS
The TPMS (Tire Pressure Sensor) Fault is usually caused by the sensor not being able to communicate with the control module. This can be caused by a number of things, such as interference. In some cases, the fault can also be caused by the sensor having a faulty battery. In such cases, it is important to replace the faulty sensor.
The tire pressure sensors are located in each of your tires. They are responsible for communicating with your vehicle’s control module when the pressure in your tires is low.
If you see a TPMS error, you should immediately take your car to the service center for help. This is especially true if you are experiencing an issue with one of your tires.
Depending on your vehicle, there may be a way to reset the TPMS manually or through your vehicle’s control center. It is recommended that you consult the owner’s manual or a professional, so you can be sure to properly reset your sensor.
For most vehicles, resetting the TPMS can be done by pressing and holding a button on the dash. This process typically takes about 20 minutes to complete.
Another common way to reset your TPMS is through the use of a TPMS tool. These tools are available at various stores and on the Internet. It is best to purchase a tool that is compatible with your vehicle’s make and model.
The TPMS tool is designed to allow you to program the sensors so they are in line with your vehicle’s specifications. This will reset your TPMS and get it back to communicating with the control module.
Some cars come with a TPMS reset tool as standard equipment, but this is not always the case. For example, some Honda models require a separate tool to be used in order to program the sensors.
If you have an aftermarket TPMS system, it may be possible to reset the TPMS by disconnecting the positive battery cable and starting your vehicle. Then, press the horn for about three seconds to discharge any excess power stored in your battery. Then, reconnect the positive battery cable and you should have your TPMS reset and working properly again.
Reprogram the TPMS
If your TPMS sensor is not working properly, it may need to be reprogrammed. A faulty sensor can be the result of a number of factors, including damaged tires, worn-out sensors, or temperature changes. Taking care of these issues right away can ensure that you avoid an accident and maintain the safety of your vehicle.
One of the main reasons why a TPMS system malfunctions is because the tire pressure sensor is incorrectly calibrated. A technician can use a scan tool to read the correct readings and reset the TPMS system.
Depending on the make and model, this procedure can take a few minutes to complete. After that, the TPMS will work again and alert you when there is a problem.
When your TPMS system detects that there is a problem, the warning light will blink and then remain illuminated. This is because the system needs time to adjust. The light will flash until you are able to fix the issue, so it’s important to schedule an appointment as soon as possible.
The TPMS is designed to alert you when your tires are underinflated, which could cause poor handling or a blowout. Underinflated tires are the cause of thousands of accidents in the United States alone.
There are two types of TPMS systems: direct and indirect. The former requires calibration after every service, while the latter does not.
If your TPMS light is not functioning correctly, it is likely that the sensor is not calibrated or the battery has died. This can be a relatively inexpensive repair.
Alternatively, if your TPMS light keeps on reappearing, it may indicate that the TPMS sensor is defective and should be replaced. You can either have your local Ford dealer replace the sensor, or you can take the car to a trusted service center like Wilson KIA for an inspection and repair.
The good news is that most TPMS sensor faults can be repaired at the shop. The technician will need to reprogram the TPMS system, which will enable it to detect when a tire has low pressure. This will help the technician avoid having to replace a sensor and save you money in the long run.
Replace the Sensor
Many people have experienced a message on their dashboard saying, “Tire Pressure Sensor Fault.” This is not only a frustrating situation but also a dangerous one. The TPMS system is designed to alert drivers if the tires are under-inflated, which can lead to flats and a loss of vehicle control.
The TPMS sensors measure the air pressure in each of your wheels and then relay that information to your vehicle’s computer. Depending on your specific model, it may display a tire pressure gauge and warn you if the pressure is too low.
There are several reasons why the tire pressure sensor may give you a “fault” message. These include over-inflation, under-inflation, a faulty sensor, and more.
A faulty sensor can cause a variety of problems, including uneven wear on your tires, which can make them squeak or make it difficult to steer. It can also trigger an underinflated or overinflated condition, which can damage your tires and reduce your fuel economy.
In addition to these issues, a faulty sensor can also cause a vibration in your steering wheel that could make it difficult to steer. These vibrations can be especially severe if you’re driving at high speed on an open road.
If you’re worried that your TPMS is faulty, you can bring your vehicle to a shop and have the problem diagnosed. The technician will use a diagnostic scan tool to check the sensors and the tires.
After the technician has determined the faulty tire pressure sensor, they will replace it with a new one. This is an essential part of any car’s TPMS system and will prevent you from experiencing serious problems in the future.
You should also have the old sensor removed from your vehicle before replacing it. This will ensure that you don’t have any old parts in the way when you install the new one.
You should also be sure that your new tire pressure sensor is calibrated properly to avoid false readings and other issues. This will help your tires last longer and avoid costly repairs. Additionally, you should always remember to keep your tire pressure up to the manufacturer’s recommended level.
