If your Honda tire pressure sensor is malfunctioning, you will want to know how to reset it. Rather than digging through the owner’s manual, this article will teach you the steps for doing so.
Resetting Honda Tire Pressure Sensor
If your Honda Tire Pressure Sensor is not working or if it needs to be reset, follow these steps:
- Park your car in a safe location.
- Open the hood and remove the air intake grill.
- Disconnect the negative battery cable.
- Remove the four screws that hold the pressure sensor cover in place.
- Lift up the pressure sensor cover and disconnect the wiring harness from the pressure sensor.
- Clean both surfaces of the pressure sensor with a damp cloth and rubbing alcohol, then reinstall the pressure sensor cover and screws. Reattach the negative battery cable before closing hood.
- Start the car and check for proper tire pressure.
Safety Precautions and Tips
If your Honda detects an incorrect pressure in one of its tires, it will issue a warning and may
activate the air pressure monitoring system. This system uses sensors to measure air pressure in each tire and sends this information to the Honda computer. If one or more of your tires is under-inflated, the computer will adjust the air pressures in all of your tires to ensure that all tires are at the correct level.
If you experience a warning from your Honda about incorrect tire pressure, here are some safety precautions you can take to avoid potential problems:
- Make sure your car is properly inflated – follow the manufacturer’s guidelines for your vehicle. Under-inflation can cause your Honda to activate the air pressure monitoring system, which can lead to inaccurate readings and dangerous situations.
- Check your tire inflation levels regularly – use a digital gauge to check inflation levels on all four tires at least once a month. Over-inflation can also cause problems with your vehicle’s suspension and braking systems, as well as decreased fuel economy. Keep an eye out for changes in inflation levels even if you don’t think they’re necessary – if one or more of your tires is significantly under-inflated, it may be time for a replacement.
- Don’t drive if one of your tires is dangerously low on air – if one or more of your tires is below the minimum required PSI (pounds per square inch), do not attempt to drive until the tire is replaced and the air pressure has been corrected. This could lead to dangerous conditions and injuries if you were to lose control of your car.
- Call a Honda mechanic if you experience any unusual or incorrect warnings from your car’s air pressure monitoring system – this may be an indication that your car needs repairs or a new air pressure sensor.
How to Reset the Honda Tire Pressure Sensor
If your Honda Tire Pressure Sensor is not reading the correct pressure, you may need to reset it.
To reset the TPMS:
- Turn off the car and remove any keys from the ignition.
- Open the passenger side door.
- Locate and press down on the release tab on top of the TPMS sensor.: Release tab for TPMS sensor To release the sensor, use a finger or a coin : Resetting TPMS with coin If needed, gently pull on the sensor until it comes free from its mountings : Resetting TPMS with finger WARNING! Do not touch or attempt to move any other part of the sensor while it is in operation as this could result in damage and loss of accuracy. Resetting TPMS with keyhole cover In order to re-attach the sensor, position it over its mounting hole and insert one end into its retaining clip, then rotate until it snaps into place .: Retaining clip for TPMS: Snap into place
Warning Signs of a Bad Tire
If you’re noticing any of the following warning signs, it might be time to check your tire pressure.
- Your car is pulling to one side when driving or turning
- Your car has a difficult time accelerating or braking
- You feel a “thumping” or vibration when driving
- You hear a strange noise from your tires
- Your car has a “flat” feeling when driving
- Your tire’s inflation pressure is significantly lower than it should be
- You have had your tire replaced recently and your car feels different when driving
Why do i need to reset the sensor
Honda Tire Pressure Sensor Reset Procedure
If your Honda Tire Pressure Sensor is not reading properly, or if you just want to reset it, follow these steps:
- Check the sensor’s connectors.
- Detach the sensor from the wheel hub using a 10mm wrench. Be careful not to damage either component.
- Clean both sides of the sensor’s connector with alcohol and a Q-tip, then reattach it to the wheel hub using the supplied screw . Tighten the screw only until it tightens evenly. Do not over-tighten as this could damage the sensor .
- Drive your vehicle for at least 10 minutes to allow air pressure in the tires to reach equilibrium .
Other reset options
There are a few other reset options you can try if the pressure sensor on your Honda tire doesn’t seem to be working. First, check that the Honda tire inflation pressure is set correctly. Next, use a air compressor to blow out any air pockets in the tire. Finally, try resetting the sensor by pressing and holding down the valve stem until the gauge goes off.
If you have a Honda, there is a good chance that the tire pressure sensor is one of your sensors that needs to be reset. This article will outline the different reset options for Honda motorcycles and how to perform each one.
There are three ways to reset a Honda’s tire pressure sensor:
1) Use the key fob
2) Remove the wheel
3) Use a HPS tool
Tire pressure monitor system:
Resetting Honda Tire Pressure Sensor
If your Honda detects low tire pressure, it will send a warning light and the system will activate the SRS airbag. To reset the tire pressure sensor on a Honda, turn off the ignition and remove the key from the ignition. Next, press and hold down both of the brake pedal’s pedals until you hear a “beep-beep” sound. Release both pedals and turn on the ignition. The “Honda Service Engine Soon” light should turn off after about five seconds. If it does not, check that your negative battery cable is connected properly at the battery and check for any obstructions in the air intake piping near your Honda’s engine.
If your Honda detects an issue with one or more of your tires, it will prompt you to reset the tire pressure monitor system. This process can help ensure accurate readings and prevent potential safety concerns.
To reset the Honda Tire Pressure Monitor System:
1) Open the Honda® Vehicle Owner’s Manual.
2) Find the section related to your vehicle’s tire pressure monitoring system.
3) Follow the instructions provided in that section.
4) Be sure to reset the system before driving again.
